Evaluation of direct light processing for the fabrication of bioactive ceramic scaffolds: Effect of pore/strut size on manufacturability and mechanical performance

Bioactive ceramic scaffolds for bone regeneration consisting of a three-dimensional mesh of interpenetrating struts with square section were fabricated via Digital Light Processing (DLP). The ability of the technique to manufacture 3D porous structures from β-tricalcium phosphate (β-TCP) powders with different dimensions of struts and pores was evaluated, identifying the possibilities and limitations of the manufacturing process. Small pore sizes were found to seriously complicate the elimination of excess slurry from the scaffold’s innermost pores. The effect of the strut/pore size on the mechanical performance of the scaffolds under compressive stresses was also evaluated, but no significant influence was found. Under compressive stresses, the structures resulted weaker when tested perpendicularly to the printing plane due to interlayer shear failure. Interlayer superficial grooves are proposed as potential failure-controlling defects, which could also explain the lack of a Weibull size effect on the mechanical strength of the fabricated DLP scaffolds.     

Fabrication and properties of 3D printed zirconia scaffold coated with calcium silicate/hydroxyapatite

The scaffold of bone repair needs a variety of material combinations to meet its intended performance; a typical single material such as zirconia has excellent mechanical properties, while hydroxyapatite and calcium silicate are bioactive materials with different degradation rates. In this paper, porous zirconia scaffolds were fabricated using 3D printing technology. The surface of the scaffold was coated by dipping with different contents of calcium silicate and hydroxyapatite to improve the biological activity and mechanical properties. Mechanical tests show that the coating material can effectively fill the pores of the porous scaffold, increasing its compressive strength by an average of 55%. The simulated body fluid (SBF) test showed that the higher calcium silicate in the coating increased the degradation rate. Cell experiments showed that the coated scaffolds exhibited good cytocompatibility and were beneficial to the proliferation and differentiation of cells. In conclusion, coated scaffolds have potential applications in the field of bone repair.     

基于测绘地理信息技术的涉地税源风险识别模式应用研究

为解决沧州市涉地税源管理手段单一等问题,文中提出以测绘地理信息技术为支撑,通过对多源数据组织管理,建立风险分析指标,采用多种GIS空间分析方法构建了涉地风险税源识别模式并在沧州进行应用。结果表明:该模式能有效识别多种涉地风险,为涉地税源管理提供了支撑。     

Preparation of faceted TaN grains by heating Ta-containing oxides in BN crucible with Na

Single-crystal grains of TaN were synthesized by heating Ta₂O₅, FeTa₂O₆, or FeTaO₄ in a BN crucible together with Na metal in an Ar atmosphere at 1100 °C. The BN crucible acted a solid source of nitrogen. Aggregates of columnar ε-TaN single crystals 10–150 μm in size were formed on the inner wall of the BN crucible when either Ta₂O₅ or FeTa₂O₆ was used. On the other hand, platelet-like single crystals of θ-TaN 1–50 μm in size were obtained from FeTaO₄. The results of wavelength-dispersive X-ray spectrometry indicated that the compositions of the ε-TaN and θ-TaN crystals were close to the stoichiometric ideal.     

江淮丘陵区马槽河流域污染源调查分析及治理建议

随着区域城市人口增加和人民生活水平提高，江淮丘陵区中小河流水环境污染问题日益突出，成为区域社会经济发展的主要制约因素之一。本文以位于江淮丘陵区马槽河流域为研究对象，通过资料收集、问卷调查、实地勘察等手段，查明该地区入河污染物指标 COD、氨氮、TN、TP 主要贡献因素及占比，其中生活污染（51%，40%，54%，28%）、面源污染(6%，38%，9%，42%)、畜禽养殖（39%，15%，17%，25%）三类型贡献占比 90%以上，内源污染和水产养殖较少。针对污染源调查结果特征，提出镇区管网完善、农村分散处理、畜禽粪污处理、养殖废水农田消纳、污染缓冲带设置、径流拦截与再利用、河流生态化改造等治理建议，可为今后中小河流污染源调查与治理提供借鉴。     

Charge source and the charging mechanism of the contact electrification of polymer powder

The charge sources, as well as the charging mechanism of the contact electrification (CE) of polymers, are still debatable. Since CE is accompanied by destruction, it is considered that “hard contacting” via ball milling can induce covalent bond scission and produce naked-activated-charge sources. Regarding “soft contacting” via nano-scale sliding, which does not induce covalent bond scission, a frontier-electron, “f-electron,” of the naked-activated-charge source is crucial to electron transfer among the naked-activated-charge sources. Here, we configure naked-activated-charge-source models, naked-activated-mechano-anion, and naked-activated-mechano-cation, which are produced by mechanical energy induced heterogeneous covalent bond scission, as well as naked-activated-mechano-radicals that are produced by homogeneous covalent bond scission. Regarding “soft contacting” among naked-activated-charge sources in a vacuum, f-electron can be transferred from a donor to an acceptor if the energy level of the donor is higher than that of the acceptor. The net amount of the normalized transferred-f-electrons is obtained by adopting settings in which the average energy level of the naked-activated-charge sources (as the donors) is higher than that of the sources employed as acceptors. Thus, the surfaces comprising the donors and acceptors will exhibit positive and negative net surface charges, respectively. We conclude that net surface charges depend on the average energy level of naked-activated-charge sources. Further, we observe that the alignment of polyethylene (PE)-polyvinyl chloride (PVC)-polytetrafluoroethylene (PTFE) to the average energy level is identical to that of the triboelectric series.     

Optical and electrical properties of ITO film on flexible fluorphlogopite substrate

Indium Tin Oxide (ITO) films were prepared, at room temperature, on a fluorphlogopite substrate using magnetron sputtering technology. At various temperatures of 500 °C, 600 °C, 700 °C, 800 °C, and 900 °C, the samples were (had) annealed for 2 h (a 2-h duration). The results showed improvement in the crystalline performance of ITO film at selected annealing temperatures, with a significant reduction in resistivity at 800 °C. The lowest resistivity is 4.08 × 10^?4 Ω-cm, which is nearly an order of magnitude lower than the unannealed sample. All samples have an average light transmittance above 85% in the visible light range (400–800 nm), and with increasing annealing temperature, the average light transmittance tends to decrease. Besides, at the sensitive wavelength of 550 nm, the light transmittance is as high as 93.74%. The sheet resistance testing of the sample was through the number of bending times, which revealed that with the increase of the number of bending, the sheet resistance increases. However, after 1200 bending times, the change rate of the sheet resistance remains below 5%. Thus, the ITO film prepared on the flexible fluorphlogopite substrate revealed excellent optical and electrical properties, good flexibility, and improved stability after high-temperature annealing, which guarantees successful application in flexible electronic devices.     

Effect of Newtonian heating/cooling on free convection in an annular permeable region in the presence of heat source/sink

The influence of Newtonian heating/cooling in the presence of heat source/sink has been investigated on laminar free convective flow in a vertical annular permeable region. The mathematical model for the problem has been considered as a boundary value problem consisting of two simultaneous ordinary differential equations. The boundary value problem has been transformed to nondimensional form. This has given rise to a number of parameters representing both geometrical and physical features of the problem. Closed‐form analytical solutions of the governing equations have been obtained for two different cases of internal heat generation/absorption. To assess the effects of governing parameters on the fluid velocity and temperature, a number of profiles of these field variables have been presented. The efficacy of the distinct processes on the field variables has been discussed extensively. The main outcome obtained in this study is that the velocity as well as temperature is enhanced in the case of the Newtonian heating while the opposite behavior occurs in the Newtonian cooling for both cases of source and sink. Furthermore, the influence of the governing parameters has been shown on the skin friction, volume flow rate, and the Nusselt number.     

Radiation and slip effects on MHD Maxwell nanofluid flow over an inclined surface with chemical reaction

The numerical solutions of the upper-convected Maxwell (UCM) nanofluid flow under the magnetic field effects over an inclined stretching sheet has been worked out. This model has the tendency to elaborate on the characteristics of “relaxation time” for the fluid flow. Special consideration has been given to the impact of nonlinear velocity slip, thermal radiation and heat generation. To study the heat transfer, the modified Fourier and Fick's laws are incorporated in the modeling process. The mass transfer phenomenon is investigated under the effects of chemical reaction, Brownian motion and thermophoresis. With the aid of the similarity transformations, the governing equations in the ordinary differential form are determined and then solved through the MATLAB's package “bvp4c” numerically. This study also brings into the spotlight such crucial physical parameters, which are inevitable for describing the flow and heat transfer behavior. This has been done through graphs and tables with as much precision and exactitude as is possible. The ascending values of the magnetic parameter, the Maxwell parameter and the angle of the inclined stretching sheet cause decay in the dimensionless velocity while an assisting behavior of the thermal and concentration buoyancy parameters is noticed.     

环境中污染源废气检测方法及影响因素分析

对污染源废气监测原理进行了简单分析,阐述了当前我国常用的环境中污染源废气检测方法,并对废气检测影响因素及质量控制进行了深入探究。